A Case Study of Path Dependent Calibration and Pillar Stability Analysis Using the LaModel Program

Details

• Personal Author:
  Sears MM
• Description:
  The LaModel program is widely used to calculate stresses and displacements on thin tabular deposits, particularly when multiple seams or complex mining geometry is encountered. The program itself allows the user to create multiple mining steps to show a progressive sequence of mining. However, LaModel considers each individual step as an independent steady-state condition, and any previous loading conditions of the materials are not tracked. It also does not consider any sort of dynamic stress change during the mining process. In certain circumstances, especially in multiple-seam situations, modeling a scenario of the seam of interest without considering the previous mining sequence in the off seams can potentially lead to inaccurate results. The primary objective of this paper is to present a situation where a potentially dynamic, unstable mining condition was encountered. It was not evident until the previous loading conditions in the off seams and the impact of dynamic stress changes in the active seam were considered. It is important to make the mining community aware of these potential modeling scenarios where the path-dependent nature of the mining sequence is of key importance. This paper presents a case history where room-and-pillar retreat mining was being conducted in a relatively deep cover stress regime where multiple seam interactions were present from both undermining and overmining. Mining in the active seam was being conducted with room-and-pillar mining techniques consisting of a series of parallel production panels being successively developed and retreat mined along a set of Mains. In this situation, the traditional global LaModel analysis without any path-dependent adjustments did not fully identify the area of poor conditions that were encountered. This paper explores the impacts of mining in the active seam on the lower seam which, in turn, has a negative impact on the active seam. This provided a solid foundation for the subsequent analysis of the three seams simultaneously. Based on the calibrated model, it is likely that retreat mining in the active seam resulted in increased stresses in the underlying seam that conceivably resulted in additional convergence and, most likely, additionally convergence of the pillars under the panel being developed. This in turn could have caused active subsidence, squeezing of the pillars, floor heave, and significant rib deterioration in the active workings. The LaModel program is extremely useful for analyzing multiple-seam mining scenarios. As multiple-seam situations become even more prevalent, the potential for encountering a path-dependent mining scenario also increases. To successfully model path-dependent mining scenarios, the ground control engineer will be required to make sound judgments on the condition of pillars in sub-adjacent seams. These engineering judgments should be based not only on the current state of stress, but also on any prior or future states of stress. This means considering the stresses from over or undermining as well as stresses applied to the sub-adjacent seams from actively mining the seam of interest. [Description provided by NIOSH]
• Subjects:
  Occupational Health Safety Software
• Keywords:
  Computer Software Ground Control Mining Engineering Pillar Design Pillar Mechanics Room And Pillar Mining
• Series:
  Mining Publications
• ISBN:
  97808733551
• Publisher:
  Society for Mining, Metallurgy & Exploration (SME)
• Document Type:
  Text
• Genre:
  Proceedings
• Place as Subject:
  OSHA Region 3 ; Pennsylvania
• CIO:
  National Institute for Occupational Safety and Health (NIOSH)
• Division:
  PMRD - Pittsburgh Mining Research Division
• Topic:
  Workplace Safety & Health
• Location:
  North America
• Pages in Document:
  65-72
• NIOSHTIC Number:
  nn:20070525
• Citation:
  Proceedings of the 43rd International Conference on Ground Control in Mining (ICGCM 2024), July 22-25, 2024, Canonsburg, Pennsylvania. Klemetti T, Mitra R, Perry K, Murphy M, Tulu IB, eds. Englewood, CO: Society for Mining, Metallurgy & Exploration (SME), 2024 Jul; :65-72
• Editor(s):
  Klemetti T; Mitra R; Perry K; Murphy M; Tulu IB
• Federal Fiscal Year:
  2024
• Peer Reviewed:
  False
• Source Full Name:
  Proceedings of the 43rd International Conference on Ground Control in Mining (ICGCM 2024), July 22-25, 2024, Canonsburg, Pennsylvania
• Collection(s):
  National Institute for Occupational Safety and Health
• Main Document Checksum:
  urn:sha-512:e3f82a57c9b6aebc2f66ed95e2874ef87e395dedeac60b8e36dd1ed954edfc62b4dfd59c7a854d570723770724f5c84d766d0e11ebfcde0787a82e6a5a6ff5d2
• Download URL:
  https://stacks.cdc.gov/view/cdc/215716/cdc_215716_DS1.pdf
• File Type:
  [PDF - 3.09 MB ]